green distributor wires

Electrical Wire Color Codes: Deciphering What Each Color Means

The purpose of green wires is to ground an electrical circuit. They connect to the grounding terminal in an outlet box and run to the ground bus bar in an electrical panel. In this way, green wires act as a failsafe, giving electricity a place to escape into the ground if a live wire within the circuit touches metal or something else conductive.

Get Price

PORSCHE 911 930 (1978-1989) Ignition Distributor Wire (Green .

PORSCHE 911 930 (1978-1989) Ignition Distributor Wire (Green Wire) BOSCH OEM +1 YEAR WARRANTY. Ignition Distributor Wire (Green Wire). PORSCHE part # 930 602 907 01. Made by BOSCH OEM. All parts have 1 year warranty.

Get Price

Anybody know what Duraspark distributor (3 wires) go to .

I've been using the yellow one for +, the black with green for - and the last one I'm assuming was to ground the distributor with the stock Duraspark module. At any rate, my ignition worked fine on the way home, I regapped the plugs (and changed to the blue Jacobs wires) to .060, and it won't run for 10 seconds, regapped back to .050 quickly .

Get Price

GM HEI Ignition Distributor Wiring Diagrams and Guide

Most of the original GM V-6 and V-8 models used an ignition coil inside the distributor cap, making it a one-piece ready-to-run distributor. HEI ignition systems are very dependable and offer great performance on a number of applications.

Get Price

MSD Tech: Distributor Troubleshooting - Holley Motor Life

If the ignition and coil check out as detailed, then the distributor pickup may be at fault. Another popular distributor is the Ready-to-Run line. These distributors are easily identified by the three pin connector that has a Red, Orange and Black wire. In some models, there will be a separate Green wire that is used for a tachometer signal wire.

Get Price

Distributor Green Wire - Partsklassik, Classic Parts for Air .

Distributor Wire This green wire connects the ignition distributor to the wiring harness. This wire sends the trigger signal, and it should not have any broken insulation or corrosion, as that will affect the signal. Fits 1978 to 1983 911SC and 1978 to 1989 turbo.

Get Price

MSD Tech: Ignition Troubleshooting - Holley Motor Life

There are two trigger inputs on the MSD; a White wire and a 2-pin connector with a Violet wire and a Green wire. These are the wires for the incoming trigger signal from the distributor. It is important to note that only one method will be used, meaning either the white wire is used, or the 2-pin connector is used.

Get Price

Ye old M110 Green Distributor wire. | Mercedes-Benz Forum

Anyway I have new ignition module, wires, coil, cap, rotor, plugs are good, and obviously the green wire from ignition module to distributor. Timing and valves checked. My friend has an '85 280TE so I had him take his ignition module off for me tp try and no spark.

Get Price

Green distributor wire: used on pre-1978 930s? - Pelican .

The Green Signal Line can be used on a CW rotating distributor by reversing the two wires going into the CDI box. And there is an adapter kit supplied by Bosch, Porsche, and wholesale suppliers like SSF. I use these and then paint the green signal wire with a BLUE stripe to signify how it is wired. Godspeed Leslie Rice Pandemonium magazine

Get Price

Spark Plug Wires and Sets at Summit Racing

All colors—blue, red, green, yellow, orange, including neon tones—are available in most diameters, including 7mm, 8mm, 10mm, and more. Get the ignition wires that withstand high temperatures and voltage loss for minimum crossfire, and are resistant to caustic chemicals like fuels, oils, and solvents.

Get Price

OEM Bosch 1234431290 Green Ignition Distributor 128mm Wire .

Porsche 911 Ignition Distributor Primary Lead Green Wire OER 93060290701. $55.53 + shipping. Seller 98.9% positive.

Get Price

HEI Distributor Troubleshooting With Performance Distributors

This is located inside the distributor, and has the green and white wires from the pick up attached on one end, and a terminal block on the other. Unfortunately, there is no test that can be performed with an ohm meter on this part. You will need to remove it and take it to an auto parts store that has a module tester.

Get Price

Product Details

Product List